Replace Easy Valve Volcano Bags

It’s easy to replace your Easy Valve bags, and get a much longer life out of the mouthpiece. I love the easy valve for many reasons, but the wasteful nature of single use was troubling. Using this trick I’ve been able to clean and keep using mouthpieces 20+ times over.

You can use the Volcano Vaporizer Easy Valve Replacement SetOven Bags or Vaporizer Bags, it doesn’t matter.

  1. Using a very small flat head screw driver, pop out the bag from the mouthpiece by sliding the flat head up between the bag and the orange plastic, and then prying the bag out. Do this slowly and carefully, and be careful.
    replace-bag-easy-valve-1 replace-bag-easy-valve-2
  2. Remove the black o-ring and the clear plastic retaining ring from inside the bag. Remove the bag and save for extraction or discard. Make sure not to loose the valve, which is a small disc of rubber. Clean all the reusable parts. I recommend hot soapy water. These plastic pieces are not as heavy duty as the rest of the Volcao and I don’t think they should be cleaned with a solvent like alcohol.
    replace-bag-easy-valve-4 replace-bag-easy-valve-5 replace-bag-easy-valve-7 
  3. Cut new bag to length if using Volcano replacement bags, the length is a matter of personal preference.
    replace-bag-easy-valve-8
  4. Prepare the new bag. Thread bag through black o-ring. Open up bag. Roll o-ring up to clear plastic retaining ring. Position at end of bag, and roll o-ring onto the clear ring so that it sits in the groove.
    replace-bag-easy-valve-10 replace-bag-easy-valve-11 replace-bag-easy-valve-12
  5. Tie off end of bag.
    replace-bag-easy-valve-9
  6. Prepare bag for assembly by folding back back over o-ring and smoothing flat. Prepare mouthpiece by assuring valve is centered and placed correctly. Place it on a flat and sturdy surface which can handle you pushing down forcefully on it.
    replace-bag-easy-valve-13 replace-bag-easy-valve-3 replace-bag-easy-valve-14
  7. Line up the bag and the mouthpiece and press strongly and directly down until the bag snaps back into place. It’s helpful to use a flat heavy object to push the bag into place and apply even presure. For example the bottom of a heavy mug, small block of wood, be creative.
    replace-bag-easy-valve-15
  8. Done – new Volcano bag for much less money and spares some waste.
    replace-bag-easy-valve-16

Save 20% WITH COUPON!

Use VTIPS20 for 20% off your entire Vapor.com order!

classic and hybrid

19 Comments

  1. AG on December 22, 2016 at 5:40 am

    What do you use to tie off the end of the bag I cant think of something that will get as good of a seal as the metal ties the original bags have.



    • Vapormaster on December 22, 2016 at 7:36 am

      I cut a small stip off the bag roll and use that like a ribbon. Ties up nice and tight and then after a double knot can be trimmed down.



    • greenbag on March 20, 2017 at 9:26 pm

      You could also just tie the end of the bag into a knot.



  2. tokemasta flex on May 2, 2016 at 7:11 pm

    > 1. Using a very small flat head screw driver, pop out the bag from the mouthpiece …

    This line, which was very conveniently at the top of the page, has here saved me hours of frustration and a $100 frustration-buy replacement starter kit. Much appreciated.



    • Wendy Hoffman on September 26, 2016 at 12:38 am

      Is there any way to extend the life of an Easy Valve bag? Also, how can you utilize the resin in the bag that’s being replaced due to leakage? Thank you



      • Vapormaster on October 3, 2016 at 6:14 am

        I don’t know of any way to extend their useful life, over time they all crack and start to leak and need to be replaced.

        The resin can be extracted a number of ways. Some folks cut the bag into strips and simmer over a low heat in butter or milk. The bags come out clean and the resin bonds to the fat molecules and then the butter or milk can be used for cooking edibles. And some people have reported success warming the use bag up and using a credit card wrapped in parchment to scrape it off.



        • Spuzzum on May 30, 2017 at 8:30 am

          Try cutting the bags into strips, then put directly into the filling chamber.. loosely. They’re heat-resistant FDA approved plastic to begin with, and should withstand the maximum temps the Volcano’s pushing into it anyway. Oven bags are generally good from 400-450F (200-230C). I’ve already tried it… got absolutely ripped. 😛



  3. 420 on July 23, 2015 at 3:04 am

    I just cut the old bag off and use Goodi Ouchless hair ties to tie new bags to the outside of the orange mouthpiece. I use two, wrapping them double, and then turn the end back down towards the bag and away from my mouth with a second band. Works great, and no threat of poking my eye out if that screwdriver slips. Mom always said I’d put someone’s eye out… so no sharp tools for me, especial around 4:20… Actually, first time around I tried to pry that sucker off, and gave up after almost jabbing my hand with the screwdriver. So, mother being the necessity of invention, or something like that, I came up with a safe, fast, cheap alternative that works great. And they say you can’t have good, cheap and fast all at the same time. Not true!!! 😉



  4. Sb on July 2, 2015 at 12:25 pm

    I can not get the mouthpiece off the bag. Can’t wedge a flat head. Can not get it off!! Any help



    • Vapormaster on July 7, 2015 at 7:04 am

      How big is your flat head? You need a pocket size screwdriver with a small tip. Sometimes soaking the mouthpiece in a bowl of hot water will soften the plastic a little bit and make it easier.



      • Doug on March 17, 2018 at 2:43 pm

        My flat head is about a size 10 hat size!



    • Doug on January 25, 2018 at 12:48 am

      Use a #1 or # 00 flat head screwdriver, such as that for watch repair or an eyeglass type screwdriver. If that wont work, mix vodka with orange juice and use that screwdriver. It won’t work on the easy valve, but you won’t care.



  5. Ian Smith on March 28, 2015 at 3:49 pm

    Hey, I was wondering what the replacement bag kit costs, and how would I go about getting one

    Thanks.



  6. Julia on September 4, 2014 at 2:47 am

    Is it supposed to be so difficult to pry out the bag? I literally have /not been able/ to complete this step no matter which tutorial I’ve consulted. Once I was finally able to get the flathead down between the bag and the outer shell, but it was super stiff and I couldn’t pry it out without the flathead popping out. To even get the flathead in between I had to brace the piece on a hard surface and use my weight. I’m not some strong dude. But I’m not petite for a woman and as a woman who grew up playing sports and roughing it on camping trips, I’m not shy about using what strength I can master to get a job done.

    Tips? Would shifting the temp of the mouthpiece body make this any easier?



    • Vapormaster on November 19, 2014 at 7:08 am

      Try soaking the mouthpiece in hot water to soften the plastic. Also, try another mouthpiece altogether – I’ve found some are more difficult than others. It gets easier the more times you pry it out. Also I find using a small screwdriver makes a difference.



  7. brendon on May 19, 2013 at 12:42 am

    Great was looking online to buy new bags and stumbled across this. Used a oven bag instead. Thanks for the tip



  8. Kevin on March 22, 2013 at 1:40 pm

    Hey! Great site! I’ve been using my volcano 5+ years and really glad I found your site, thank you for sharing.

    Kev